Language
language
中国
韩国
韩国
韩国
韩国
韩国
NEWS CENTER
DWSK Sprocket
Position:
Home
/
/
/
Idler Sprocket with ball bearing on sales manufacturing process

Idler Sprocket with ball bearing on sales manufacturing process

(Summary description)Idler Sprocket with ball bearing on sales is a kind of rolling bearing. The spherical alloy steel ball is installed in the center of the inner ring and outer ring, and the friction force in the process of power transmission is reduced by rolling method and the transmission power of mechanical power is improved. Ball bearings cannot accept large and heavy loads and are more common in light industrial machinery. Ball bearings are also called ball bearings.

Idler Sprocket with ball bearing on sales manufacturing process

(Summary description)Idler Sprocket with ball bearing on sales is a kind of rolling bearing. The spherical alloy steel ball is installed in the center of the inner ring and outer ring, and the friction force in the process of power transmission is reduced by rolling method and the transmission power of mechanical power is improved. Ball bearings cannot accept large and heavy loads and are more common in light industrial machinery. Ball bearings are also called ball bearings.

Information

Idler Sprocket with ball bearing on sales is a kind of rolling bearing. The spherical alloy steel ball is installed in the center of the inner ring and outer ring, and the friction force in the process of power transmission is reduced by rolling method and the transmission power of mechanical power is improved. Ball bearings cannot accept large and heavy loads and are more common in light industrial machinery. Ball bearings are also called ball bearings.
Idler Sprocket with ball bearing on sales are generally used in low-load mechanical transmission equipment. Due to the small bearing area of ​​ball bearings, serious mechanical damage is prone to occur under high-speed operation. Therefore, needle roller bearings are often used in heavy-load mechanical transmission to increase the bearing surface, improve mechanical transmission power and reduce mechanical Sexual damage.
Idler Sprocket with ball bearing on sales changes the conflict mode of the bearing and chooses the rolling friction. This method is more useful to reduce the conflict between the bearing surfaces, effectively improve the service life of the fan bearing, and thus extend the service life of the radiator. The disadvantage is that the process is more messy, leading to higher costs, and at the same time, higher operating noise.
Because of the different types of Idler Sprocket with ball bearing on sales, structural types, service levels, skill requirements, materials, and batch sizes, the fundamental production process is not exactly the same.


The machining process of the main parts of the Idler Sprocket with ball bearing on sales is as follows:
1. The processing process of the ferrule:
The processing of the inner ring and outer ring of the bearing differs depending on the raw material or blank method. The process before turning can be divided into the following three types. The entire processing process is: Bar or tube (some bars require After casting, annealing and normalizing)-turning-heat treatment-grinding-lapping or polishing-final inspection of parts-rust prevention- Warehousing----(To be installed together)
2. Processing process of steel balls:
The processing of steel balls also differs according to the conditions of the raw materials. The process before frustration or photoballing can be divided into the following three types. The process before heat treatment can be divided into the following two types. The entire processing process It is: cold punching of bar or wire (some bars need to be punched and annealed after cold punching)-frustration, rough grinding, soft grinding or smooth ball-heat treatment-hard grinding- ---Fine grinding-lapping or grinding-final inspection grouping-rust prevention, packaging-storage (to be installed in a set).
3. The process of Idler Sprocket with ball bearing on sales processing:
The processing of ball bearings varies according to the different raw materials. The process before heat treatment can be divided into the following two types. The entire process is: bar turning or wire rod cold heading after stringing and soft grinding-heat treatment ----String soft point----Rough grinding outer diameter----Rough grinding end face----final grinding end face----fine grinding outer diameter----final grinding outer diameter----final Inspection group-rust prevention, packaging-warehousing (to be assembled and installed). 

Keyword:

Scan the QR code to read on your phone

DWSK SPROCKET

ADD: Shimenqiao Industrial Zone, Renqiu City, Hebei Province, China
TEL: 
0086-317-2805558
FAX: 0086-317-2805556
QQ: 1148504595
E-MAIL:
dwsk@vip.126.com

Alibaba: DongWang Sprocket

COPYRIGHT © RenQiu Dong Wang Machinery Parts Co., Ltd.         冀ICP备19028325号-1       Power by 300.cn